PHILIPS HTS3251B/F7 - HTS3051BV/F7 BLU RAY HOME THEATER SYSTEM INITIALIZING AND POWER SUPPLY CIRCUIT

PHILIPS HTS3251B/F7 - HTS3051BV/F7 

 BLU RAY

 HOME THEATER SYSTEM 

 INITIALIZING AND POWER SUPPLY CIRCUIT 

HOW TO INITIALIZE THE BLU-RAY DISC HOME THEATER
[HTS3251B/F7]
To put the program back at the factory-default, initialize the BD player as the following procedure.
Note: By initializing, network is reset to disconnected state and “Network Service Disclaimer” appears on the screen.
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order. (All VFD lights)
4. Press [ STOP ] button on the remote control unit.
CLEAR WILL DISPAY ON VFD
5. To exit this mode, press [ POWER ] button.
[HTS3051B/F7]
To put the program back at the factory-default, initialize the BD player as the following procedure.
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order. (All VFD lights)
4. Press [ STOP ] button on the remote control unit.
CLEAR WILL DISPAY ON VFD
5. To exit this mode, press [ POWER] button.
FIRMWARE RENEWAL MODE
1. Turn the power on and remove the disc on the tray and close the tray.
2. To put the BD player into version up mode, press
[9], [8], [7], [6], and [DISC MENU/POP-UP MENU] buttons on the remote control unit in that order. The tray will open automatically.
3. Load the disc for version up.
4. The BD player enters the F/W version up mode automatically. Make sure to insert the proper F/W for the state of this model.
5. After programming is finished, the checksum on the VFD.
Checksum appears on the VFD then the tray will open automatically. Remove the disc on the tray. At this time, no button is available.
6. Unplug the AC cord from the AC outlet. Then plug it again.
7. Turn the power on.
All the settings will be put back to factory default.
How to Verify the Firmware Version
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order.
4. To exit this mode, press [ POWER] button.
Error Code (vTuner – HTTP Status Code)
Status Code
Description
201 Created
A new resource was created by this unit’s request.
202 Accepted
This unit’s request was accepted but its processing is not completed.
204 No Content
Though the server processed the request, there was no content.
304 Not Modified
This unit caches latest resource and the requested resource is not modified. (exception protocol error)
400 Bad Request
The server cannot understand this unit’s request.
401 Unauthorized
The resource this unit has requested needs to be authorized.
403 Forbidden
The server has received the requests from this unit but refused to process them.
404 Not Found
The URI this unit has requested is not found.
500 Internal Server Error
Internal server error occurred.
501 Not Implemented
The server does not support functionalities required to process the request from this unit.
502 Bad Gateway
The proxy server between this unit and the server received an invalid reply from another proxy or the original server.
503 Service Unavailable

Because of overloading or maintenance, the server is temporarily unavailable.

Error Code table (vTuner – Application Status Code)
Status Code
Description
001 Nothing List
As a result of list creation process, there is no item to be displayed from the received data.
002 LAN Disconnect
This unit’s LAN is disconnected.
005 Favorite Error
The URL needed to register or delete favorite data is not sent from the server.
601 Stream Stop

Because the streaming stopped, decoding has stopped. (This error message is displayed if decoding is disabled for 20 seconds.)
602 Unsupported(Info)
The stream information of the broadcast is unsupported.
603 Decode Timeout
The unit tried to playback the received stream data, but the data was not played correctly even after three minutes elapsed.
604 Unsupported(Stream)
As a result of analyzing the received stream data, the data is unsupported.
605 Decode Failed
The received stream data cannot be decoded.
606 Multi Stream

Because this unit received multiple streaming data, the data cannot be
decoded.
701 Protocol Error
An exception error occurred during communication between the server or the broadcast.
702 Start Up Error
The application of this unit failed to start.
703 URL Error
The URL which this unit specified is in invalid form.
705 Connect Failed

Connection with the proxy which exists between this unit and the server or the broadcast has failed. (IP conversion error)
706 Connect Failed
Connection with the server or the broadcast has failed. (IP conversion error)
707 Connect Failed
Connection with the server or the broadcast has failed.
723 Analyze Error
The received protocol data cannot be analyzed.
727 System Error(Memory)
A system error occurred in the unit. (memory shortage, internal cURL pro cessing error)
728 Response Timeout
A response timeout occurred to unit’s connection request.
743 System Error(Program)
A system error occurred in the unit. (program error, internal cURL processing error)
745 System Error(LAN Port)
A system error occurred in the unit. (LAN unusable, internal cURL processing error)
752 Response Timeout
A response timeout occurred to unit’s connection request.
755 Disconnect Error(Send)

Because the connection between this unit and the server or the broadcast was disconnected, it has failed to send the protocol data.
756 Disconnect
Error(Receive)
Because the connection between this unit and the server or the broadcast was disconnected, it has failed to receive the protocol data.
761 Analyze Error
The received protocol data cannot be analyzed.
790 List Not Found
The list information which was sent from the server is invalid or not found.
791 Stream Timeout
The stream data is not sent from the broadcast.

POWER SUPPLY CIRCUIT 
CLICK ON THE IMAGES TO ZOOM IN

POWER BOARD